"NP6050维修资料"
"制作:WGF"
"共页, 第页"
,,"CANON 佳能 NP-6050(NP6750/6550/6450)复印机故障码"
,"E000,E001,E002,E003,E004,E005,E013,E020 故障码清除"
,,"进入维修程序模式*4*;按 \"〈 \" 键,或按 \" 〉\" 键,选择ERROR后按\"*\"键清除故障码"
,"E202,E204(键盘锁住) 故障码清除"
,,"进入维修程序模式*1*;检查\"B-ERR1\";\"B-ERR2\";\"B-ERR3\"检查故障码性质"
,"WIRE:",,"显示数不为\"0\"表示高压电极丝清洁器未停止在原位"
,"复印机本体故障码"
,,"定影故障E00"
,"E000",,"予热未完成",,,,,,,"电源开关ON后5分钟热敏电阻TH1检测到定影温度低于70度,热敏电阻TH1开路;定影灯H1开路;热敏开关TSI开路;固态继继电器SSR故障;主板故障"
,"E001",,"定影超温",,,,,,,"热敏电阻TH1检测到定影温度超过230度达2秒,热敏电阻TH1短路;"
,"E002",,"予热异常",,,,,,,"定影温度达到70度后,3分钟内未达到100度;定影温度达到100度后,未达到150度"
,"E003",,"予热异常",,,,,,,"定影温度达到100度,3分钟后定影温度又低于70度"
,"E004",,"SSR短路",,,,,,,"电源开关ON后,当定影启动信号(HTRD)为OFF时却检测到SSR导通信号(SSR ON)达3秒"
,"E005",,"定影清洁卷筒纸故障",,,,,,,"定影清洁卷筒纸用完传感器PS11"
,"E010",,"主电机M1故障",,,,,,,"电机启动后,1秒内未产生2个以上时钟脉冲"
,"E013",,"废粉输送故障",,,,,,,"废粉输送螺旋杆不转动",,,,,,,,"MSW4"
,"E014",,"搓纸电机M2故障",,,,,,,"电机启动后,1秒内未产生2个以上时钟脉冲"
,"E020",,"墨粉电机故障",,,,,,,"墨粉搅拌电机M10,加粉电机M11;复印时加粉信号保持\"0\"达2分钟以上,新机安装时加粉信号保持\"0\"达10分钟以上"
,"E030",,"总计数器CNT1开路",,,,,,,"计数器驱动信号Off时检测到计数器CNT1开路"
,"E031",,"选购件计数器CNT2开路",,,,,,,"计数器驱动信号Off时检测到计数器CNT2开路"
,"E050",,"双面X向拍纸故障",,,,,,,"双面X向拍纸电机启动4秒内未产生X向原位信号HTXHP;产生X向原位信号HTXHP达2秒以上"
,"E051",,"双面Y向拍纸故障",,,,,,,"双面Y向拍纸电机启动4秒内未产生Y向原位信号HTYHP;产生Y向原位信号HTYHP达2秒以上"
,"E202",,"扫描电路(键盘锁住)",,,,,,,"电源开关ON后或按复印键后10秒内,未产生扫描原位信号SCHP;产生扫描原位信号LXHP达2秒以上"
,"E203",,"扫描电路故障",,,,,,,"扫描电机M3启动后产生0.5秒以上的扫描原位信号SCHP"
,"E204",,"扫描电路(键盘锁住)",,,,,,,"扫描电机M3前进0.8秒内未产生扫描首页边界信号SCDP1,SCDP2"
,"E210",,"镜头X向移动故障",,,,,,,"电源开关ON后或按复印键后9秒内,未产生X向原位信号LXHP;产生X向原位信号LXHP达2秒以上"
,"E212",,"镜头Y向移动故障",,,,,,,"电源开关ON后或按复印键后9秒内,未产生Y向原位信号LYHP;产生Y向原位信号LYHP达2秒以上"
,"E213",,"扫描器锁定故障",,,,,,,"在滑动阅读模式输出扫描器锁定指令后一定时间未收到锁定信号,锁定传感器PS48,锁定电磁铁SL1或主板故障"
,"E240",,"主板电路故障",,,,,,,"主板Q156与Q140之间通信出错"
,"E243",,"主板/操作面板电路故障",,,,,,,"主板Q156与操作面板的Q937之间通信出错"
,,,"复印机选购件RF-D1输稿器故障"
,"E400",,"ADF电路通讯故障",,,,,,,"主板与ADF板通讯出错"

下一页